OUCG8D-525M-A Factory OEM Car Remote Clicker Replacement
mouseover to zoom or click to enlarge
  • OUCG8D-525M-A Factory OEM Car Remote Clicker Replacement
  • OUCG8D-525M-A Factory OEM Car Remote Clicker Replacement
Product ID 7626246
Brand Mitsubishi
Condition Refurbished

OUCG8D-525M-A Factory OEM Car Remote Clicker Replacement by Mitsubishi

USD $32.77 Free Shipping
Hurry, only 3 left!

Have one to sell? Sell Yours Now

Details: This is a Factory OEM (Original Equipment Manufacturer) 2 button keyless entry remote, aka "key fob" for Mitsubishi. See "Compatibility Tab" for a full list of compatible vehicles. These are genuine OEM electronics in a new aftermarket case. Programming Instructions: Diagram of Data Link Connector (DLC) Programming Procedure for Eclipse, Lancer, and Outlander Obtain all remote transmitters for this vehicle. This procedure's a little more complicated than others, we recommend having someone help you perform this procedure. 1. Locate the Data Link Connector (DLC). It will be in the trunk or under the dash on the drivers side. You may need to lay on the floor and look up to easily access it. Use the diagram above to identify ports 1 and 4. Notice that the DLC connector is tapered. You can use this to help identify the proper ports. Be sure there's metal contact pins in ports 1 and 4. 2. Insert key into the ignition and leave in the OFF position. 3. Using a suitable jumper wire, jump pin 1 to pin 4. Jump means to make a connection between the two pins using any metal wire. A paperclip bent in the shape of a "U" usually works perfect. Be certain the jumper wire makes contact with the pins in ports 1 and 4. Once the jumper wire is installed it needs to remain there throughout this procedure until instructed to remove. 4. Within ten seconds of connecting the jumper wire, press the hazard light switch 6 times. The doors will automatically lock and unlock once indicating the vehicle is in programming mode. 5. Now press the LOCK button on the first remote to be programmed THREE TIMES within ten seconds. The doors will automatically lock and unlock once indicating the vehicle has programmed that remote. 6. If you have additional remotes to program, repeat step 5 within one minute. 7. Once all remotes are programmed remove jumper. Test all remotes to ensure proper programming. Programming Procedure for 00-04 Montero Sport Obtain all remote transmitters for this vehicle. This procedure's a little more complicated than others, we recommend having someone help you perform this procedure. 1. Locate the Data Link Connector (DLC). It will be under the dash on the drivers side. You may need to lay on the floor and look up to easily access it. Use the diagram above to identify ports 1 and 4. Notice that the DLC connector is tapered. You can use this to help identify the proper ports. Be sure there's metal contact pins in ports 1 and 4. 2. Insert key into the ignition and leave in the OFF position. 3. Using a suitable jumper wire, jump pin 1 to pin 4. Jump means to make a connection between the two pins using any metal wire. A paperclip bent in the shape of a "U" usually works perfect. Be certain the jumper wire makes contact with the pins in ports 1 and 4. Once the jumper wire is installed it needs to remain there throughout this procedure until instructed to remove. 4. Within ten seconds of connecting the jumper wire, turn the ignition switch to ACC (switch to ON position for some?00 models) then back to OFF, THREE times*. You must do this step very quickly; all three cycles should take 2-3 seconds. (ON is the position just shy of cranking the engine; ACC is the position when you turn the key back towards yourself; OFF is the position where you can remove your key). The doors will automatically lock and unlock once indicating the vehicle is in programming mode. 5. Now press the LOCK button on the first remote to be programmed THREE TIMES within ten seconds. The doors will automatically lock and unlock once indicating the vehicle has programmed that remote. 6. If you have additional remotes to program, repeat step 5 within one minute. 7. Once all remotes are programmed remove jumper. Test all remotes to ensure proper programming. * If you are getting no response from turning the ignition from ON to OFF, Then try the step turning the ignition from OFF to ACC. The?00 Montero sport was the first vehicle with this procedure and it was changed for the?01 model year from ON to OFF, to ON to ACC. Programming Procedure for 97-99 Montero Sport Obtain all remote transmitters for this vehicle. 1. Open the driver's door. 2. Turn the ignition key ON (ON is the position just shy of cranking the engine). 3. Press and hold the programming/override button (located under or at the bottom of the driver's side dash). In approximately 20 seconds the system will start to cycle the door locks and the siren (if equipped) 3 times to indicate the system has entered the transmitter learn mode (DO NOT RELEASE THE PROGRAMMING/OVERRIDE BUTTON). 4. Press the #1 button (top left button) on the un-programmed transmitter. The system will respond by cycling the door locks and the siren (if equipped) one time to indicate the transmitter has been learned. 5. All other transmitters (up to four) also need to be programmed at this time. 6. Programming is now complete, let go of the programming/override button and turn ignition off to exit learn mode. Test all remotes for proper programming. OUCG8D-525M-A | | CANADA: 850104241A | FCC ID: OUCG8D-525M-A | 2 BUTTON | OMRON G8D-525M-A
Brand:MitsubishiCondition:Refurbished
MPN:OUCG8D-525M-A SKU:OUCG8D-525M-A

Be the first to review this product! Have you purchased this product in the past, or have experience with it? Be sure to pass your opinion on to our other users!

There are no Customer Reviews yet

Accepted Payment Methods

Shipping & Handling

Store Location Omaha, NE
Ships within 1 business days
Shipping Options Standard Shipping (3-7 days)
Ships to Contiguous U.S., AK, HI, PR, APO/FPO/DPO, PO Boxes
Shipping Rates
Shipping Costs are different for every product sold by this seller.

Shipping & Payment Policies

Simply look for the logo to enjoy free DOMESTIC shipping on ALL items throughout the store. THAT'S RIGHT, FREE DOMESTIC SHIPPING ON ALL PURCHASES!We Ship using USPS First Class Mail with Delivery Confirmation. All orders are processed within in 1 business day of purchase. International Shipping rates apply. Below is a map on estimated delivery times by state.

Returns Policy

Item(s) must be returned within 60 days after arrival.
Refund will be given as: Refund Money.

At Keyless Entry Remote Inc we strive to make your transaction as easy as possible. We offer a 30 day, 100%, no questions asked return policy so you can buy with confidence! All of our vehicle remotes are tested with a RF signal tester to ensure functionality.

Ask us first before going to the dealer, we can try and save you even more money by providing you with FREE programming instructions!

Our Money Back Guarantee:

For any reason you are not completely satisfied with your remote purchase, simply return within 30 days of purchase with a note containing reason for return and your contact information (name, address, phone #, email address) to:

Keyless Entry Remote Inc
Attn: Returns
10306 Ellison Circle
Omaha, NE 68134

Once we receive the remote back we will issue you a full refund; it's that easy! We understand that your lives may be hectic and before you know it, the 30 days have passed. For this reason we offer a 60 day extended refund/exchange policy. A 20% restocking fee will be applied to all refunds or exchanges processed after 30 days of purchase. Refunds/exchanges will not be accepted after 60 days from purchase. Any expedited shipping charges will not be refunded in any case.

If you purchase a "Flash Service", this is non-refundable. Please make sure if you are ordering a flash service that you have all of your programming needs verified before purchase. If you have questions please don't hesitate to call us at 402-671-5100.